自上料攪拌車計量系統在攪拌站中是不能缺少的，如果少了計量系統，攪拌站的各個環節會變得很麻煩，各種原材料都需要先自己稱量，然后在進行混合攪拌，這會浪費許多時間，也會浪費人力。因此，計量系統也是需要經常維護的。

The metering system of the self feeding mixer truck is indispensable in the mixing plant. Without the metering system, each link of the mixing plant will become very troublesome. All raw materials need to be weighed first and then mixed, which will waste a lot of time and manpower. Therefore, the metering system also needs regular maintenance.

1.自上料攪拌車所有軟連接的紅膠管和稱量斗中的波紋管在自然狀態時不受拉力，否則會影響稱量精度。

1. All soft connected red rubber hoses and corrugated pipes in the weighing hopper of the self feeding mixer truck are not subject to tension in the natural state, otherwise the weighing accuracy will be affected.

2.自上料攪拌車傳感器安裝好后，只能承受正壓力(對于懸臂式或壓式傳感器)或正拉力(對于s型或拉式傳感器)，不能承受扭矩。

2. After the sensor of the loading mixer is installed, it can only bear the positive pressure (for cantilever type or pressure type sensors) or the positive tension (for s-type or pull type sensors), but cannot bear the torque.

3.對于同一桿稱，其傳感器(3個或4個)須同型號同規格。因此安裝傳感器時一定要檢查其銘牌上的內容是否一致，不同規格的傳感器其外型有可能相同。

3. For the same scale, its sensors (3 or 4) must be of the same model and specification. Therefore, when installing the sensor, be sure to check whether the contents on the nameplate are consistent. Sensors of different specifications may have the same appearance.

4.在稱量斗上進行電焊作業時，須斷開控制電源，并將傳感器短接或把電焊機的地線直接搭在稱量斗上，避免焊接時過大的電流通過傳感器而將其損壞。

4. When conducting electric welding on the weighing bucket, the control power supply must be disconnected, and the sensor shall be short circuited or the ground wire of the electric welding machine shall be directly laid on the weighing bucket to avoid damage caused by excessive current passing through the sensor during welding.

5.自上料攪拌車，撾式傳感器(s型)安裝好后，需擰緊鎖緊螺母，懸吊螺桿不能質住傳感器槽型根部，即懸吊螺桿與型傳感器槽型根部應留有10mm左右的間隙。

5. After the loading mixer truck and the Laos sensor (s type) are installed, the lock nut shall be tightened. The suspension screw cannot hold the root of the sensor groove, that is, a gap of about 10mm shall be left between the suspension screw and the root of the sensor groove.

自上料攪拌車計量系統的五點維護要求就講解到這里了，您想在后期的時間內容安全順利且高質量的操作攪拌車進行工作，就要對其多個方面的要點以及問題加以了解?？梢詠砦覀兙W站http://www.bookmarkpostings.com做參考資訊查看！

The five points of maintenance requirements for the metering system of the charging mixer have been explained here. If you want to operate the mixer safely, smoothly and with high quality in the later period, you should understand the key points and problems in many aspects. You can come to our website http://www.bookmarkpostings.com See the reference information!